Catalina 350 International Association

Mine, hull #357, is in aft cabin, port side, lower cabinet on the aft wall.

As John Forr mentioned, we did the trip in his 350 Forr Fun. Crossed the Lake with no problems at all. Also done it outside, so here are some timings for you: 1. Lake Worth to No Name Harbor 13 hrs off shore, to Duck Key 8 hrs Hawke Channel, to Key West 8 hrs in Hawke Channel, Key West to St Pete of...

I am sorry Russ, but I could not help myself when I read your post. Of course you had to install it "upside down". Consider where your boat is compared to where Kevin's is likely to be!!

BTW: see your email about next year.

Bruce

I have hull 357, so there is a chance it will be similar to your 358.

The AC fan runs continually while the AC is on, regardless of compressor. Switch tanks, bow and stern via valves under floor panel under galley sink, our hot water is same pressure as cold.

Enjoy a great boat mate

Bruce

John: the only answer to stop the delamination is to buy a boat without lamination! Sorry to be so crass, but it appears Catalina may have had a problem with workers and/or glue around 2004/2005. According to Pandy/Douglas/Butler there is no good cure once it has happened. Sorry mate. We did find th...

I had severe delimitation up until about 4 years ago. Had tried “ironing” the laminate back (the glue was heat activated), done the Triumph trick and used some wood glue (the best outcome) but to no avail. May have lasted a few weeks and then back to square one. Had previously contacted Catalina, we...

Gary: attached are two pictures of the back of my tachometer if that helps you at all. Sorry, did not remove the screw for fear of consequences.

Testing replies, do not respond please.

This is Bruce Whyte, current editor of the C350 section of Mainsheet and Webmaster for the c350 site I am looking for as many pictures as possible of 350s for inclusion in a reworked website. Do you still have all those sent to you in 2013? If so, would you send them to me please? Use bruce@yachting...

Out of interest, has your tacho totally ceased working or does it move but to bizarre readings, like 3,000 when you are idling. If the latter you only need make an adjustment to correct. Either way I would try: Remove the plate holding your instruments on the pedestal; Turn it over and have a look a...

I replaced the original tank monitor about a year ago. I made sure the forward was empty which allowed to place the tape. I had the tape loosely attached to a paint stirring stick, placed it and used the stick to smooth it down. Aft tank was straight forward.

Dave: please send the picture to me and I think it should grace our website somewhere if you agree. bmwhyte@bellsouth.net

Bruce

Thank you for the navigation but we are flying through eastern Florida. Left Brunswick, GA on Tuesday morning, Fernandina Beach that night, St Augustine the next night and tonight in Cocoa Beach, maybe watch the liftoff as a bonus. Planning on starting on the OKeechobee on day and completing the jou...

Welcome Seredipity from Aussie Mate, hull #357. By chance we are bring C350, Forr Fun to Punta Gorda and will be in Halifax Harbor Marine this Thursday night. Want to catch up before Tampa? Is Halifax an OK overnight stop?

Bruce Whyte
Aussie Mate

Hey Wally et al, see y'all soon.

Measurements from our hull 357, MkI C350: Port side: 18x18 inches, double bag, inboard clasps are 9 inches front to middle and 7.25 middle to rear, outboard 17 inches apart. Stb: 13x13 inches, double bag, inboard clasps are 6.25 inches front to middle and 5 inches middle to rear, outboard 12 inches ...

Triumph, does this allow breeze to come through? Where does it fix to?

Dennis I will let you know thanks.

I also have a Snake River tank monitor. It has caused problems for years. I have re-taped the sensor tape twice but it regularly reads a tank as full when it is empty. The holding tank must only hold about 12 gallons based on the frequency the monitor tells me to empty. So I also am interested in a ...

Good luck. We used acetone to dissolve the previous glue which worked really well. The contact glue we used from 3M (sorry cannot remember if it was 90) worked too well. Once applied to both surfaces it stuck and would not allow any movement. Hence we could not slide the panel into the grooves at th...

Another as can only upload one at a time.