Catalina 350 International Association

Thanx for your reply 'yodagwb'. What brand of LED anchor light assembly did you replace it with? What year is your C-350, mine is a 2005 # 368?
Just want to ensure that the original anchor light assemblies are the same.
Thanx,
Jim

Thanx for your response Bill and Mark but I was asking for the brand of the fixture atop the mast, not the replacement bulb type. I already have the bulb information from your previous posts.
Thanx,
Jim

I have a 2005 C350 #368 and wish to replace my anchor light bulb with an LED bulb. Does anyone know the brand (Hella, Imtra, etc.) of the actual fixture and bulb that came with the boat from the factory?
Thanx,
Jim

Ken - Hull # 368 is 1 1/4 since I've mounted several Nav Pods with that dimension.

Hello Bill, just seeing your post. I have the same analog thermostat as you do and purchased an exact replacement from Fisheries Supply. The part is
Item ID: DOM F1710 and was $149.48 (free shipping). Their number is 206-632-4462 and they are on PDT.
Hope you're successful.
Cheers, Jim

I have now had a chance to use my box mounted seal (as opposed to the factory door mounted seal) while cruising and it works like a dream. The door closes tighter with no cold air escaping around the seal and the seal itself hasn't twisted.
Cheers, Jim

I used Trim-Lok 135 D-Seal. See pic.
Cheers, Jim

Well, the frig door seal worked well for a while with the spacers in the hinges, but eventually twisted the seal on that side. So, this winter I took the door off (have gotten good at that now) and removed the old seal from the door itself. I took new seal (in one piece from a roll) and placed it on...

PYI's Maxprop Easy is the best, in my humble opinion, feathering prop (don't need a folding) out there for the M35B w/ Hurth xmission. It's easy to install and the pitch can be adjusted in the water, although mine with a 15/9 from the factory works great. Merry Christmas from the lower mid- Chesapea...

Ken, yes I am but remarkably when I tried it yesterday the pump pulled the a/f from the Sea Flush system as it's supposed to do. Go figure!!
Thanx, Jim

Weird subject I know but after changing the impeller, the pump will pump the cooling water but NOT the a/f which I am supplying through a Sea Flush kit into the Groco water strainer with all components tight. I hold the a/f container above the level of the strainer and even move the hose around some...

Terri - Found the fitting and opened it but not much coolant came out, guess I had gotten most of it out with the Heat Exchanger drain petcock. Next time I will open this fitting first and then the exchanger petcock. Emptied and cleaned the overflow tank and refilled. Used about 1 & 1/4 gallons ...

Thanx Terri - I'm heading to the boat this afternoon and will try to find it.
Cheers, Jim

I've read several good articles in the Form relative to changing engine (35-B) coolant but can't find one showing/locating the drain locations. There is a drain petcock on the bottom of the heat exchanger and obviously at the thermostat housing (which I would think would be to purge air from the sys...

I have bent (the piling didn't give) the left flange outward of the starboard roller tray so that it interferes with the positioning of my new Rocna 15 anchor on the port roller and tray. I have tried to "pound" that flange inward to its original position without success. Any ideas on bend...

I finally used the freezer/fridge last weekend (I don't keep it on when I'm not on the boat) and it DID NOT leak any cold air from around the gasket after installing the spacer under each door hinge between the hinge and the fridge itself (see my previous post). And it has not twisted the gasket at ...

Thanx folks for all of the knowledgeable discussion surrounding the Rocna anchor. As soon as I save a few $100 bills I will buy a Rocna 15 and use in place of my Bruce. Cheers, Jim
PS - Monty (Steve), I will see you this Thursday...

I've read all of the anchor related posts in the Forum and it seems like the Rocna 15kg 33lb is the anchor of choice for "normal, non-hazardous anchoring". I currently have the same size Bruce anchor which works fairly well except in mud. The Bruce also has a straight shank the works well ...

Dana - If I measure the temp within the cold plate box with a laser temp gauge, it's read 15 - 20 which is where I store my gin & tonic ice so that's good. The main part of the freezer box however hovers around 35 and the fridge around 40. Each time I start-up the refrigeration system, which is ...

Thanx Ken - I have ordered a buzzer from Catalina Direct (probably cost more than from your source) and according to pics shown with it, the outside ring which you see on the front side of the panel unscrews from the main body of the buzzer which is behind the panel. Hope I can get my ring off witho...